Register | Sign In


Understanding through Discussion


EvC Forum active members: 64 (9164 total)
4 online now:
Newest Member: ChatGPT
Post Volume: Total: 916,840 Year: 4,097/9,624 Month: 968/974 Week: 295/286 Day: 16/40 Hour: 0/1


Thread  Details

Email This Thread
Newer Topic | Older Topic
  
Author Topic:   10 cubits across and 30 cubits around
johnfolton 
Suspended Member (Idle past 5619 days)
Posts: 2024
Joined: 12-04-2005


Message 3 of 10 (98266)
04-06-2004 10:51 PM
Reply to: Message 1 by RAZD
04-06-2004 10:13 PM


I was just replying to Eta Carinae, suggestion that the bible is in error in respect to pi, you have all the dimensions to make the casting, the diameter is in respect to the outside of the container, as is the height, the circumference is in respect to the inside of the container, and it says the container is to be round all about, so the verse isn't in error in respect to pi, but knowing pi we can calculate the thickness of the vessel, I came up with 5.65 inches, I'll just bet if you lay a ruler and measure the breath of a normal mans hand it will be closer to 5.65 inches than 3 inches, so leaning its the mold was based off the 25 inch sacred cubit, etc...
P.S. It doesn't matter the inside dimension circumference is going to be different than the outside circumference, because we know pi, and that the outside diameter is 10 cubits, we then know the outside circumference will be 31.4 cubits, and the inside diameter is 9.55 cubits, etc...though bet the person that made the molds, hand width was 5.65 inches wide, but he didn't need a handbreath measurement to make the mold, he only needed the three measurements, 5 cubits, 10 cubits, and 30 cubits, etc...
[This message has been edited by whatever, 04-06-2004]

This message is a reply to:
 Message 1 by RAZD, posted 04-06-2004 10:13 PM RAZD has replied

Replies to this message:
 Message 4 by SRO2, posted 04-06-2004 11:18 PM johnfolton has replied
 Message 5 by RAZD, posted 04-06-2004 11:24 PM johnfolton has not replied

johnfolton 
Suspended Member (Idle past 5619 days)
Posts: 2024
Joined: 12-04-2005


Message 7 of 10 (98286)
04-06-2004 11:40 PM
Reply to: Message 4 by SRO2
04-06-2004 11:18 PM


Two chapiters were made for Solomons Temple
Rocket, Its all about the two chapiters made of molten brass that were made for Solomons temple, that sat on top of two pillars to contain the bath waters, etc...
Abbyleever, I actually hear you, if the cubit was a bit less than 25 inches it would bring the hands width closer to 4 to 5 inches, but the problem isn't really about the cubit, but pi, but agree with you, there is no problem with pi, etc...
[This message has been edited by whatever, 04-06-2004]

This message is a reply to:
 Message 4 by SRO2, posted 04-06-2004 11:18 PM SRO2 has replied

Replies to this message:
 Message 8 by SRO2, posted 04-06-2004 11:54 PM johnfolton has replied

johnfolton 
Suspended Member (Idle past 5619 days)
Posts: 2024
Joined: 12-04-2005


Message 9 of 10 (98309)
04-07-2004 1:10 AM
Reply to: Message 8 by SRO2
04-06-2004 11:54 PM


Re: Two chapiters were made for Solomons Temple
Rocket, Noah had 120 years to build the ark, probably would of contracted some of the work, if you take the bible literally, they were giants in those days, and had iron and brass technology, though super sized boats are not limited to Noahs ark, whatabout the chinese building super large boats over 600 feet long, by compartmentalizing them, to strengthen them, thought as legend goes, they incorporated sails, ruled the south seas, this has already been discussed on this very forum, apparently its not all that hard to build a super large wooden vessel if one compartmentalizes, etc...
P.S. Its off topic, just thought I'd give you someone that not a creationists saying its not only possible, but that he believes the Chinese built boats larger than the ark, etc...
http://EvC Forum: About that Boat - Noah's Ark -->EvC Forum: About that Boat - Noah's Ark
Message 2 of 167 09-20-2002 01:50 PM

This message is a reply to:
 Message 8 by SRO2, posted 04-06-2004 11:54 PM SRO2 has not replied

Newer Topic | Older Topic
Jump to:


Copyright 2001-2023 by EvC Forum, All Rights Reserved

™ Version 4.2
Innovative software from Qwixotic © 2024